Skip to main content

Ladder Program Example for Lifter Application

Ladder Program Example for Lifter Application



Ladder Program to carry parts to three positions using the lift.



Control Specifications


The following operation should be performed in this unit.

Study the required specifications and then create the program and confirm the operation


Overall control


  • When [PB1] (X20) on the operation panel is pressed, Supply command(Y0) for the hopper is turned ON.When [PB1] (X20) is released, Supply command (Y0) is turned OFF. When Supply command (Y0) is turned ON, the hopper supplies a part.
  • When [SW1] (X24) on the operation panel is turned ON, the conveyors move forward. When [SW1] (X24) is turned OFF, the conveyors stop.
  • After the sensor X10, X12or X14 at the left of conveyor has detected a part, the corresponding conveyor is set ON and carries it to the tray at the right end.The conveyor stops 3seconds after a part has passed the sensor X11, X13 or X15at the right of conveyor.
  • Large, medium and small parts on the conveyor are sorted by the input of sensors Upper (X0), Middle(X1) and Lower (X2).

·       

Lift Control


    1)       When the sensor for Part on lift (X3) in the lift is turned ON, a part is carried to either of the following conveyors according to its size.

  • Large part: Upper conveyor
  • Medium part: Medium conveyor
  • Small part: Lower conveyor


     2)       Lift up command (Y2) and Lift down command(Y3) are controlled according to the lift position detected by the following sensors.

  • Upper: X6
  • Meddle: X5
  • Lower: X4


     3)       When a part is transferred from the lift to the conveyor, Lift rotation command (Y4) is set ON. 


     4)       After a part is transferred, the lift is to return to the initial position and stand by.


Ladder Program Description:

In this exercise, the size of parts carried on the conveyor is to be sorted using three sensors shown on the table.


Part size
Upper (X0)
Medium (X1)
Lower (X2)
Large
ON
ON
ON
Medium
OFF
ON
ON
Small
OFF
OFF
ON

The lift stop position is determined based on the input status of the position sensors X4to X6.

When distributing a small part, the lift does not move vertically. Only the rotation of the lift 
should be controlled in the initial position.


·         Turn ON [SW1] (X24) on the operation panel.

Result >>The conveyor moves to the right.


·         Press [PB1] (X20) on the operation panel.

Result >>A part is supplied from the hopper.


·         Operation of the lift

Result >>When a large or medium part is put on the lift, the lift moves up to the upper or middle conveyor and stops. When a small part is put on the lift, the lift remains in the initial position

·         Transfer of a part


Result >>After the lift rotates and a part is transferred to the conveyor, the conveyor moves to the right and the part is carried to the tray.

·         Return of the lift


Result >>The lift with no part returns to the initial position and stops there.

·         Repeated operation


When [PB1] (X20) is pressed, the operations starting from 2 are repeated.







http://news.chivindo.com/813/ladder-program-example-for-lifter-application.html

Comments

Post a Comment

Popular posts from this blog

BT-BASIC commands used

8.10     Some of the most frequently used BT-BASIC commands used are: msi                               Changes default working directory. Mass storage is            Same as “msi” cat                               Catalogs (list)the node names in the specified directory.             get                               Brings the contents of a file into the system workspace.             load                             Same as “get”.             msi$                            Returns the directory pathname of the current working directory.             msi “..”                       Backs up one directory level.             findn                            Locates the next occurrence of the a given sting in the workspace. 8.11           If you wish to invoke the HP Board Graphics Viewer, type board graphics at the BT-BASIC command line and press the “ENTER” key on the keyboard. 8.12           A HP Board Graphics Viewer window should now appear
1 comment
Read more

Perhitungan & Cara Merubah Kumparan Blender Dari 220 V Menjadi 12 V

          Seperti yang telah dijelaskan pada buku “menggulung motor listrik arus bolak-balik, servis peralatan listrik rumah tangga kelompok penggerak dan perbaikan peralatan listrik pertukangan”, bahwa motor penggerak yang digunakan pada perlatan listrik rumah tangga dan pertukangan seperti blender, mixer, bor tembak, gerinda dsb menggunakan jenis motor universal. Motor universal adalah jenis motor listrik yang dapat disuplai dengan sumber listrik arus bolak-balik (AC) dan arus searah (DC). Jadi peralatan-peralatan listrik rumah tangga dan pertukangan tersebut yang biasanya kita suplai dengan sumber listrik AC dari PLN atau Genset sebesar 220 V sebenarnya dapat juga kita suplai dengan sumber listrik DC yang tentunya tegangan juga harus sama yakni 220 V.           Yang menjadi permasalahan bagaimana kalau peralatan listrik rumah tangga atau pertukangan tersebut, sebagai contoh misalkan blender yang ingin digunakan atau dioperasikan pada tempat yang tidak terdapat sumber listrik PLN ata
1 comment
Read more

BT-BASIC command line

8.8       At the BT-BASIC command line type the command  msi  and the directory path, then press the “ENTER” key on the keyboard.  Example:                   msi ‘/hp3070/boards/aspect/main’ 8.9       At the BT-BASIC command line type the command  get ‘testplan’ and press the   ENTER” key on the keyboard.  You should now see the body of the testplan file displayed in the work space of the BT-BASIC window. 8.10     Some of the most frequently used BT-BASIC commands used are:
Post a Comment
Read more

Autodesk SketchBook Pro 2021 Full Version

BAGAS31 – Sesuai dengan namanya, Autodesk SketchBook Pro 2021 Full Version ini merupakan software digital sketching atau drawing terbaik yang bisa kamu gunakan. Pada versi terbaru kali ini, ada beberapa penambahan fitur yang sangat efektif. Dengan fitur baru tersebut, diharapkan mampu meningkatkan proses sketching maupun drawing kamu. Autodesk SketchBook sendiri sudah bisa kamu dapatkan secara gratis melalui website resminya. Namun untuk kamu yang mau download versi Autodesk Sketchbook Pro, maka bisa langsung download melalui link yang sudah saya sediakan di bawah ini. Download Autodesk SketchBook Pro 2021 Full Version Screenshot: System Requirements: Windows 10 2.5 – 2.9 GHz of Intel or AMD CPU 4 GB of Memory 256 MB Graphics card with OpenGL 2.0 support We recommend that you use a pressure-sensitive tablet and pen for basic features Download: Autodesk SketchBook Pro 2021 Full Version [ FileUp ][ Uptobox ][ UsersDrive ] Jamu Only [ FileUp ][ Uptob
2 comments
Read more

Testhead

4.3         Testhead The testhead is that portion of the tester that supports the PIN, ASRU and Controller cards.   The testhead is divided into two BANKS and each BANK is divided into two MODULES, see figure 2 below.  Bank 1 contains modules 0 and 1, bank 2 contains modules 2 and 3.  The test fixtures are placed on the banks of the tester and locked down for board testing.  The testhead cards interface to the test fixture through the spring loaded pogo pin “nails” at the top edge on each of these card types. 4.4       Support Bay The support bay is a stand-alone cabinet that houses the power supplies for the Unit Under Test.  This bay also houses the test station power distribution unit and test station controller on earlier models. 4.5       Emergency Shutdown Switch The emergency shutdown switch is the large red button located at the lower left corner on the front of the testhead.  It turns off all AC power to the testhead, and is equivalent to turning off the m
Post a Comment
Read more

Kelebihan dan Kekurangan Saluran Listrik Jenis Saluran Udara dan Saluran Bawah Tanah

Berdasarkan pemasangannya,   saluran distribusi dibagi menjadi dua kategori, yaitu : saluran udara (overhead line) merupakan sistem penyaluran tenaga listrik melalui kawat penghantar yang ditompang pada tiang listrik. Sedangkan saluran bawah tanah (underground cable) merupakan sistem penyaluran tenaga listrik melalui kabel-kabel yang ditanamkan di dalam tanah. 1.    Saluran Bawah Tanah (Underground Lines) Saluran distribusi yang menyalurkan energi listrik melalui kabel yang ditanam didalam tanah. Kategori saluran distribusi seperti ini adalah yang favorite untuk pemasangan di dalam kota, karena berada didalam tanah, maka tidak mengganggu keindahan kota dan juga tidak mudah terjadi gangguan akibat kondisi cuaca atau kondisi alam. Namun juga memilik kekurangan, yaitu mahalnya biaya investasi dan sulitnya menentukan titik gangguan dan perbaikannya. Kedua cara penyaluran memiliki keuntungan dan kerugian masing-masing. Keuntungan yang dapat diperoleh dari suatu jaringan bawah tanah adalah
Post a Comment
Read more