Testhead

4.3 Testhead

The testhead is that portion of the tester that supports the PIN, ASRU and Controller cards. The testhead is divided into two BANKS and each BANK is divided into two MODULES, see figure 2 below. Bank 1 contains modules 0 and 1, bank 2 contains modules 2 and 3. The test fixtures are placed on the banks of the tester and locked down for board testing. The testhead cards interface to the test fixture through the spring loaded pogo pin “nails” at the top edge on each of these card types.

4.4 Support Bay

The support bay is a stand-alone cabinet that houses the power supplies for the Unit Under Test. This bay also houses the test station power distribution unit and test station controller on earlier models.

4.5 Emergency Shutdown Switch

The emergency shutdown switch is the large red button located at the lower left corner on the front of the testhead. It turns off all AC power to the testhead, and is equivalent to turning off the main circuit breaker on the rear of the support bay. Press the emergency shutdown switch if you ever need to power down the testhead and its associated equipment in an emergency situation.

CAUTION: DO NOT use the emergency shutdown switch as a substitute for

correct power-down procedures; i.e., executing the “testhead

power off” command.

Frequent use of the emergency shutdown switch can cause premature failure of the main circuit breaker on the rear of the support bay.

To restore power after pressing the emergency shutdown switch, turn on the main circuit breaker on the rear of the support bay.

4.6 Guided Probe

A convenient holder for the guided probe is provided at the upper corner on the front of the testhead. When not using the guided probe, store it in its holder.

5.0 POWERING UP THE TESTER

5.1 Locate the tester circuit breakers, they are on the rear panel of the power distribution unit,

in the enclosure mounted to the right hand side of the testhead or in the support bay. Place the circuit breakers in the “on” position.

5.2 Ensure that the test station controller (Signal Processor Unit, SPU), located in the

enclosure mounted on the left hand side of the testhead or in the support bay, is turned on.

Caution: On systems with separate SPU and disk drive units, turn on the power to the disk drive and peripheral devices prior to powering up the SPU. Be sure to allow time for the disk drives to spin up to speed before applying power to the SPU.

5.3 Ensure that the test station monitor and strip printer are both turned on.

5.2 Ensure that the UUT power supplies located in the support bay are turned on.

Comments

BT-BASIC commands used

8.10 Some of the most frequently used BT-BASIC commands used are: msi Changes default working directory. Mass storage is Same as “msi” cat Catalogs (list)the node names in the specified directory. get Brings the contents of a file into the system workspace. load Same as “get”. msi$ Returns the directory pathname of the current working directory. msi “..” Backs up one directory level. findn Locates the next occurrence of the a given sting in the workspace. 8.11 If you wish to invoke the HP Board Graphics Viewer, type board graphics at the BT-BASIC command line and press the “ENTER” key on the keyboard. 8.12 A HP Board Graphics Viewer window should now appear

Perhitungan & Cara Merubah Kumparan Blender Dari 220 V Menjadi 12 V

Seperti yang telah dijelaskan pada buku “menggulung motor listrik arus bolak-balik, servis peralatan listrik rumah tangga kelompok penggerak dan perbaikan peralatan listrik pertukangan”, bahwa motor penggerak yang digunakan pada perlatan listrik rumah tangga dan pertukangan seperti blender, mixer, bor tembak, gerinda dsb menggunakan jenis motor universal. Motor universal adalah jenis motor listrik yang dapat disuplai dengan sumber listrik arus bolak-balik (AC) dan arus searah (DC). Jadi peralatan-peralatan listrik rumah tangga dan pertukangan tersebut yang biasanya kita suplai dengan sumber listrik AC dari PLN atau Genset sebesar 220 V sebenarnya dapat juga kita suplai dengan sumber listrik DC yang tentunya tegangan juga harus sama yakni 220 V. Yang menjadi permasalahan bagaimana kalau peralatan listrik rumah tangga atau pertukangan tersebut, sebagai contoh misalkan blender yang ingin digunakan atau dioperasikan pada tempat yang tidak terdapat sumber listrik PLN ata

BT-BASIC command line

8.8 At the BT-BASIC command line type the command msi and the directory path, then press the “ENTER” key on the keyboard. Example: msi ‘/hp3070/boards/aspect/main’ 8.9 At the BT-BASIC command line type the command get ‘testplan’ and press the ENTER” key on the keyboard. You should now see the body of the testplan file displayed in the work space of the BT-BASIC window. 8.10 Some of the most frequently used BT-BASIC commands used are:

Autodesk SketchBook Pro 2021 Full Version

BAGAS31 – Sesuai dengan namanya, Autodesk SketchBook Pro 2021 Full Version ini merupakan software digital sketching atau drawing terbaik yang bisa kamu gunakan. Pada versi terbaru kali ini, ada beberapa penambahan fitur yang sangat efektif. Dengan fitur baru tersebut, diharapkan mampu meningkatkan proses sketching maupun drawing kamu. Autodesk SketchBook sendiri sudah bisa kamu dapatkan secara gratis melalui website resminya. Namun untuk kamu yang mau download versi Autodesk Sketchbook Pro, maka bisa langsung download melalui link yang sudah saya sediakan di bawah ini. Download Autodesk SketchBook Pro 2021 Full Version Screenshot: System Requirements: Windows 10 2.5 – 2.9 GHz of Intel or AMD CPU 4 GB of Memory 256 MB Graphics card with OpenGL 2.0 support We recommend that you use a pressure-sensitive tablet and pen for basic features Download: Autodesk SketchBook Pro 2021 Full Version [ FileUp ][ Uptobox ][ UsersDrive ] Jamu Only [ FileUp ][ Uptob

Kelebihan dan Kekurangan Saluran Listrik Jenis Saluran Udara dan Saluran Bawah Tanah

Berdasarkan pemasangannya, saluran distribusi dibagi menjadi dua kategori, yaitu : saluran udara (overhead line) merupakan sistem penyaluran tenaga listrik melalui kawat penghantar yang ditompang pada tiang listrik. Sedangkan saluran bawah tanah (underground cable) merupakan sistem penyaluran tenaga listrik melalui kabel-kabel yang ditanamkan di dalam tanah. 1. Saluran Bawah Tanah (Underground Lines) Saluran distribusi yang menyalurkan energi listrik melalui kabel yang ditanam didalam tanah. Kategori saluran distribusi seperti ini adalah yang favorite untuk pemasangan di dalam kota, karena berada didalam tanah, maka tidak mengganggu keindahan kota dan juga tidak mudah terjadi gangguan akibat kondisi cuaca atau kondisi alam. Namun juga memilik kekurangan, yaitu mahalnya biaya investasi dan sulitnya menentukan titik gangguan dan perbaikannya. Kedua cara penyaluran memiliki keuntungan dan kerugian masing-masing. Keuntungan yang dapat diperoleh dari suatu jaringan bawah tanah adalah

HP3070 TESTER

Search This Blog