Skip to main content

MECHANICAL FITTER INTERVIEW QUESTIONS AND ANSWERS



MECHANICAL FITTER INTERVIEW QUESTIONS AND ANSWERS

1.     Define Valve?

               Valve is a Mechanical flow control element in the process.

2.     What are types of valves?
·        Gate Valve
·        Globe Valve
·        Ball valve
·        Butterfly Valve
·        Needle Valve
·        Plug Valve
·        Diaphragm Valve
·        Non-Return Valve
·        Knife Edge Valve
·        Drain Valve
·        Float Valve
·        Flush Bottom Valve
·        Pinch Valve
·        Pen Stack Valve etc.

3.     Explain the valve parts?

A.    Gate Valve – Body, Bonnet, Seat, Gate, Stem, Hand Wheel, Gland Bush, Gland Flange, Gland Bolt and Nuts. Hand Wheel lock nut.

B.     Ball Valve – Body , End Piece , Ball , Stem , Seal , Seal Follower , Seat , Lock Nut , Handle Gland Packing , Gland Flange , Gland Stud and nut.


C.     Globe Valve – Body , Bonnet , Seat , Plug , stem ,  Hand Wheel , Lock Nut ,Gland Packing , Gland Flange , Gland Stud and nut.

D.    Butterfly – Body , Disc , Stem , Seat ring , Seat ring holder , Bush , End cover , Hand Wheel  or Gear Box , Gland Bush , Gland Packing , Gland Flange , Gland Stud and nut.


 
4.     What are the types of Gaskets?

·        CAF – Compressed Asbestos Fiber Filled Gasket
·        Semi Metallic Gasket 
·        Metallic Gasket
·        Rubber Gasket
·        Teflon Gasket
·        Spiral Wound Gasket
·        RTJ – Ring Type Joint
·        Graphite Gasket
·        Impregnated Gasket
·        Graf oil Gasket  

5.     What is Gasket? Where it is used?

·        It is sealing member between two flanges.

Uses:

1.     Water Line, Gas Line, Air Line used CAF Gasket.
2.     RTJ – High Pressure Line.
3.     Chemical Line – Rubber Gasket and Teflon Gasket.
4.     Steam Line – Semi Metallic, Metallic and Graphite.
5.     Impregnated Gasket – Valve Sealing Gasket.
6.     Spiral Wound – Steam Line.

6.     What is flange? Types of Flanges?

Flanges used to connect both lines (Fluid, Gas, Oil, Water….)

                                   Thread Type Flange
            Modified Flange
            Weld Neck Flange
            Slip On Flange
            Goose Neck Flange
            Socket Weld Flange
            Stepped Flange
            Spade Flange
            Spectacle Flange
            Blind Flange

7.     What is Gland packing? Uses of gland packing?

Gland packing is a Sealing member between two moving parts or stationary.
It is used for arrest the leak through shaft various lines.
            1. Teflon Gland packing
            2. Graphite Gland packing
            3. Carbon Gland packing
            4. Virgin PTFE Gland packing
            5. Graf oil Gland packing
8.     What are PRV and PSV?
PRV(Pressure Relief valve) release excessive more than set point, released fluid re circulated.

PSV(Pressure Safety Valve) released pressure more than set point to safe the equipments.

9.     Give the parts name of PSV?

            Body
            Bonnet
            Nozzle
            Disc
            Disc Holder
            Stem
            Blow down ring
            Blow down ring lock screw
            Spring Bottom Plate
            Spring
            Spring Top Plate
            Control Screw
            Lock Nut
            Cap
            Gasket

10.                  What is the use of SPADE, SPECTACLE, and BLIND?

SPADE- Give space between two flanges and give flow through the spade.
SPECTACLE – Combination of SPADE and BLIND and both option done in one flange.
BLIND – Used for close the line.

11.                  What is PPE?

PPE- Personnel Protective Equipment
E.g.) Helmet, Boiler Shout, Safety Goggles, Safety Shoe, Gloves, Dust Mask etc... 

12.                  What is heat exchanger? What are the types of heat exchanger?

It is an Equipment to use for Exchange the heat(Cooling or Heating purpose)
Types:
            Fixed Tube Heat Exchanger
            Floating Tube Heat Exchanger
            U Tube Exchanger
            Plate Type Exchanger
            Fin Fan Cooler Heat Exchanger
            Bridge Lock Exchanger

13.                  Explain the following valves Shell and Seat Testing?

Ball Valve
Gate Valve
Globe Valve
Butterfly valve
Plug valve

Shell Test of above valves:- 

             Testing flange to be fixed on both sides. Pressurized one side under the valve partial open condition as per the standard. Check the leakage through body, Bonnet sealing area, Gland packing area.

Seat Test of above valves:-

            Testing flange to be fix on one side of the valve. Pressurized the valve under fully closed condition as per the standard. Check the leakage through Seat in opposite side. Follow the same procedure while checking the another seat except Globe and Butterfly.

14.                  What are the testing mediums used for testing?

            Water, DM Water, Air, Kerosene, Oil, Soap water.

15.                  What is Steam trap and Gas trap?

Steam trap using for removal of Water from Steam.
Gas trap using for removal of water from gas.

16.                  What is the use of Vacuum Breaker?

It is used to remove Vacuum (Air Bubbles) from Water line.

17.                  What is the use of Ejector?

Ejector is used to create Vacuum for process.

18.                  Define Non Sparking Tools? 

Non Sparking tools used in Gas, Oil and Chemicals.
E.g. Brass hammer, Brass Wedge, Brass Spanner, Copper hammer, Copper rod , Brass rod , Brass chisel  , Rubber hammer , Nylon hammer. 

19.                  What is Strainer?

Strainer is a control element to arrest dust from flowing fluids.

20.                  What is work permit system?

Work Permit is an Authority for doing work in a process plant.
Types:

Cold Work Permit- Without Sparking, Without Heat etc.
Hot Work Permit- With heat (Grinding, Cutting, Welding)
Note: Two times only extend the permit after the normal valid of permit.
http://news.chivindo.com/493/mechanical-fitter-interview-questions-and-answers.html

Comments

Post a Comment

Popular posts from this blog

BT-BASIC commands used

8.10     Some of the most frequently used BT-BASIC commands used are: msi                               Changes default working directory. Mass storage is            Same as “msi” cat                               Catalogs (list)the node names in the specified directory.             get                               Brings the contents of a file into the system workspace.        ...
1 comment
Read more

Perhitungan & Cara Merubah Kumparan Blender Dari 220 V Menjadi 12 V

          Seperti yang telah dijelaskan pada buku “menggulung motor listrik arus bolak-balik, servis peralatan listrik rumah tangga kelompok penggerak dan perbaikan peralatan listrik pertukangan”, bahwa motor penggerak yang digunakan pada perlatan listrik rumah tangga dan pertukangan seperti blender, mixer, bor tembak, gerinda dsb menggunakan jenis motor universal. Motor universal adalah jenis motor listrik yang dapat disuplai dengan sumber listrik arus bolak-balik (AC) dan arus searah (DC). Jadi peralatan-peralatan listrik rumah tangga dan pertukangan tersebut yang biasanya kita suplai dengan sumber listrik AC dari PLN atau Genset sebesar 220 V sebenarnya dapat juga kita suplai dengan sumber listrik DC yang tentunya tegangan juga harus sama yakni 220 V.           Yang menjadi permasalahan bagaimana kalau peralatan listrik rumah tangga atau pertukangan tersebut, sebagai contoh misalkan blender yang ingin digunakan atau dioper...
1 comment
Read more

BT-BASIC command line

8.8       At the BT-BASIC command line type the command  msi  and the directory path, then press the “ENTER” key on the keyboard.  Example:                   msi ‘/hp3070/boards/aspect/main’ 8.9       At the BT-BASIC command line type the command  get ‘testplan’ and press the   ENTER” key on the keyboard.  You should now see the body of the testplan file displayed in the work space of the BT-BASIC window. 8.10     Some of the most frequently used BT-BASIC commands used are:
Post a Comment
Read more

Autodesk SketchBook Pro 2021 Full Version

BAGAS31 – Sesuai dengan namanya, Autodesk SketchBook Pro 2021 Full Version ini merupakan software digital sketching atau drawing terbaik yang bisa kamu gunakan. Pada versi terbaru kali ini, ada beberapa penambahan fitur yang sangat efektif. Dengan fitur baru tersebut, diharapkan mampu meningkatkan proses sketching maupun drawing kamu. Autodesk SketchBook sendiri sudah bisa kamu dapatkan secara gratis melalui website resminya. Namun untuk kamu yang mau download versi Autodesk Sketchbook Pro, maka bisa langsung download melalui link yang sudah saya sediakan di bawah ini. Download Autodesk SketchBook Pro 2021 Full Version Screenshot: System Requirements: Windows 10 2.5 – 2.9 GHz of Intel or AMD CPU 4 GB of Memory 256 MB Graphics card with OpenGL 2.0 support We recommend that you use a pressure-sensitive tablet and pen for basic features Download: Autodesk SketchBook Pro 2021 Full Version [ FileUp ][ Uptobox ][ UsersDrive ] Jamu Only [ File...
2 comments
Read more

Testhead

4.3         Testhead The testhead is that portion of the tester that supports the PIN, ASRU and Controller cards.   The testhead is divided into two BANKS and each BANK is divided into two MODULES, see figure 2 below.  Bank 1 contains modules 0 and 1, bank 2 contains modules 2 and 3.  The test fixtures are placed on the banks of the tester and locked down for board testing.  The testhead cards interface to the test fixture through the spring loaded pogo pin “nails” at the top edge on each of these card types. 4.4       Support Bay The support bay is a stand-alone cabinet that houses the power supplies for the Unit Under Test.  This bay also houses the test station power distribution unit and test station controller on earlier models. 4.5       Emergency Shutdown Switch The emergency shutdown switch is the large red button located at the lower left corne...
Post a Comment
Read more

Kelebihan dan Kekurangan Saluran Listrik Jenis Saluran Udara dan Saluran Bawah Tanah

Berdasarkan pemasangannya,   saluran distribusi dibagi menjadi dua kategori, yaitu : saluran udara (overhead line) merupakan sistem penyaluran tenaga listrik melalui kawat penghantar yang ditompang pada tiang listrik. Sedangkan saluran bawah tanah (underground cable) merupakan sistem penyaluran tenaga listrik melalui kabel-kabel yang ditanamkan di dalam tanah. 1.    Saluran Bawah Tanah (Underground Lines) Saluran distribusi yang menyalurkan energi listrik melalui kabel yang ditanam didalam tanah. Kategori saluran distribusi seperti ini adalah yang favorite untuk pemasangan di dalam kota, karena berada didalam tanah, maka tidak mengganggu keindahan kota dan juga tidak mudah terjadi gangguan akibat kondisi cuaca atau kondisi alam. Namun juga memilik kekurangan, yaitu mahalnya biaya investasi dan sulitnya menentukan titik gangguan dan perbaikannya. Kedua cara penyaluran memiliki keuntungan dan kerugian masing-masing. Keuntungan yang dapat diperoleh dari suatu jaringan bawah...
Post a Comment
Read more